YASKAWA MP Manual do Utilizador

Yaskawa MP SeriesEthernet Driver Help© 2012 Kepware Technologies

Yaskawa MP Series Ethernet Driver Help3. Double-click on Scan Time Setting.4. In Scan Time, note the High Speed Scan Setting and Low Speed Scan Settin

Yaskawa MP Series Ethernet Driver Help5. When the scan time settings are set, close the Scan Time dialog.www. kepware.com11

Yaskawa MP Series Ethernet Driver Help6. Double-click on Module Configuration to open the Engineering Manager.7. In the Engineering Manager, select th

Yaskawa MP Series Ethernet Driver Help8. In Slot details, double-click 218IF to open the Ethernet Interface dialog.9. Click on the Transmission Parame

Yaskawa MP Series Ethernet Driver Help10. If there is the possibility of a device connection from another LAN, set the Network Subnet Mask andGateway

Yaskawa MP Series Ethernet Driver HelpHardware Configuration for MPxxxxiecFor information on configuring an MPxxxiec device, refer to the instructions

Yaskawa MP Series Ethernet Driver Help4. In the upper-right corner, enter the device's IP Address. Then, click Connect.5. In the Project Window T

Yaskawa MP Series Ethernet Driver Help6. Then, do the following:l Check Enable Controller as a Modbus Slave.l In I/O Task Assignment, select FastTsk.l

Yaskawa MP Series Ethernet Driver Help10. The following categories should be displayed:11. To create a new variable, right-click on the desired group

Yaskawa MP Series Ethernet Driver Help12. In the Address column, specify the MotionWorks IEC Pro 1.2.3.12 address.13. Once all changes are complete, b

Yaskawa MP Series Ethernet Driver HelpTable of ContentsTable of Contents 2Yaskawa MP Series Ethernet Driver Help4Overview4Device Setup 5Memory Mapping

Yaskawa MP Series Ethernet Driver Help2. In Value, select or type the new value. Then, click Overwrite.Hardware Configuration for MPxxxx (218IF Module

Yaskawa MP Series Ethernet Driver HelpNote: The image below shows how the Input DWG Name dialog is displayed.Drawing L in Low Scan ProgramsThe first l

Yaskawa MP Series Ethernet Driver HelpLadder L01The next ladder program is Ladder L01, which initializes the Message Receive parameters and manages th

Yaskawa MP Series Ethernet Driver Helpwww. kepware.com23

Yaskawa MP Series Ethernet Driver Helpwww. kepware.com24

Yaskawa MP Series Ethernet Driver Helpwww. kepware.com25

Yaskawa MP Series Ethernet Driver Helpwww. kepware.com26

Yaskawa MP Series Ethernet Driver Helpwww. kepware.com27

Yaskawa MP Series Ethernet Driver HelpLoad and Save the ConfigurationAfter the ladders have been edited, verify and load them to the Controller. Then,

Yaskawa MP Series Ethernet Driver HelpOptimizing Yaskawa MP Series Ethernet CommunicationsThe Yaskawa MP Series Ethernet Driver has been designed to p

Yaskawa MP Series Ethernet Driver HelpSlave device '<device name>' has failed39Slave device '<device name>' is busy39T

Yaskawa MP Series Ethernet Driver HelpData Types DescriptionData Type DescriptionBoolean Single bitWord Unsigned 16 bit valuebit 0 is the low bitbit 1

Yaskawa MP Series Ethernet Driver HelpAddress Descriptions for MPxxxx (218IF Module) DevicesThe default data types for statically defined tags are sho

Yaskawa MP Series Ethernet Driver Help2.To address a string starting at MW40500 with a length of 78 bytes and Lo-Hi byte order, enter:MSL40500.78Note

Yaskawa MP Series Ethernet Driver Help3. Double Address %IL30688 [2][2] would be %IL30688 + ([2]*[2] * 8) – 8 = %IL30712.Output Register Arrays QW, QL

Yaskawa MP Series Ethernet Driver HelpError DescriptionsThe following error/warning messages may be generated. Click on the link for a description of

Yaskawa MP Series Ethernet Driver HelpA tag address that has been specified statically references a location that is beyond the range of supported loc

Yaskawa MP Series Ethernet Driver HelpDevice address '<address>' is Read OnlyError Type:WarningPossible Cause:A tag address that has b

Yaskawa MP Series Ethernet Driver HelpDevice Specific MessagesDevice '<device name>' block request [<start address> to <end a

Yaskawa MP Series Ethernet Driver HelpIllegal data address in block [<start address> to <end address>] on device'<device name>&

Yaskawa MP Series Ethernet Driver HelpSolution:Correct the function code, and then retry the query.Illegal function code '<hex function code&g

Yaskawa MP Series Ethernet Driver HelpYaskawa MP Series Ethernet Driver HelpHelp version 1.032CONTENTSOverviewWhat is the Yaskawa MP Series Ethernet D

Yaskawa MP Series Ethernet Driver HelpUnable to bind to adapter: '<adapter>'. Connect failedError Type:FatalPossible Cause:The device

Yaskawa MP Series Ethernet Driver HelpPossible Cause:The device could not negotiate with the operating systems winsock 1.1 functionality.Solution:Veri

Yaskawa MP Series Ethernet Driver HelpIndexAAddress '<address>' is out of range for the specified device or register 34Address Descrip

Yaskawa MP Series Ethernet Driver HelpEError Descriptions 34FFailure to start Winsock communications 37Float 30HHardware Configuration for MPxxxx (218

Yaskawa MP Series Ethernet Driver HelpMissing address 36OOptimizing Yaskawa MP Series Ethernet Communications 29Overview 4SShort 30Slave device '

Yaskawa MP Series Ethernet Driver HelpDevice SetupSupported DevicesMPxxxx (218IF Module). This includes any controller that uses the 218IF module.MPxx

Yaskawa MP Series Ethernet Driver HelpMemory Mapping for MPxxxxiec DevicesThis driver (Master) communicates via Modbus TCP to MPxxxxiec Series control

Yaskawa MP Series Ethernet Driver HelpSee Also: Address Descriptions for MPxxxxiec DevicesCommunications Parameterswww. kepware.com7

Yaskawa MP Series Ethernet Driver HelpDescription of the parameter is as follows:l Port Number: This parameter specifies the TCP/IP port number that t

Yaskawa MP Series Ethernet Driver HelpRegister AddressesInput registers (IW, IL, IF) and output registers (MW, ML, MF) can be read from 1 to 120 locat