Yaskawa Sigma II Indexer Manual do Utilizador Página 182
- Página / 227
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Sigma II Indexer User’s Manual SGDH Servo Amplifier Status Display Tables
9-11
9.3 SGDH Servo Amplifier Status Display Tables
9.3.1 SGDH Servo Amplifier Alarm Display Table
A summary of alarm displays and alarm code outputs is given in the following table.
Alarm
Display
Alarm Code Output
ALM
Output
Alarm Name Description
ALO1 ALO2 ALO3
A.02
OFF OFF OFF OFF
Parameter Breakdown
*
EEPROM data of servo amplifier is
abnormal.
A.03
Main Circuit Encoder
Error
Detection data for power circuit is abnor-
mal.
A.04
Parameter Setting Error
*
The parameter setting is outside the
allowable setting range.
A.05
Servomotor and Ampli-
fier Combination Error
Servo amplifier and servomotor capaci-
ties do no match each other.
A.10 ON OFF OFF OFF
Overcurrent or Heat Sink
Overheated
*2
An overcurrent flowed through the IGBT.
Heat sink of servo amplifier was over-
heated.
A.30
ON ON OFF OFF
Regeneration Error
Detected
Regenerative circuit is faulty
Regenerative resistor is faulty.
A.32 Regenerative Overload
Regenerative energy exceeds regenera-
tive resistor capacity.
A.40
OFF OFF ON OFF
Overvoltage
Main circuit DC voltage is excessively
high.
A.41 Undervoltage
Main circuit DC voltage is excessively
low.
A.51 ON OFF ON OFF Overspeed
Rotational speed of the motor is exces-
sively high.
A.71
ON ON ON OFF
Overload: High Load
The motor was operating for several sec-
onds to several tens of seconds under a
torque largely exceeding ratings.
A.72 Overload: Low Load
The motor was operating continuously
under a torque largely exceeding ratings
A.73 Dynamic Brake Overload
When the dynamic brake was applied,
rotational energy exceeded the capacity
of dynamic brake resistor.
A.74
Overload of Surge Cur-
rent Limit Resistor
The main circuit power was frequently
turned ON and OFF.
A.7A
Heat Sink Overheated
**
The heat sink of servo amplifier over-
heated.
- Safety Information 3
- Overview 8
- Using This Manual 9
- Safety Precautions 10
- 1.1 Introduction 15
- Figure 1.5 17
- Table 1.3: Part Numbers 18
- Figure 1.8 21
- Installation 22
- 2.1 Storage Conditions 23
- 2.2 Installation Site 24
- 2.3 Orientation 25
- 2.4 Installation 26
- Connectors 28
- 3.1 I/O Signals (CN1, CN4) 29
- CNIO Dual Port RAM 30
- (ON when in-position) 30
- Programmable 30
- 10250–52A2JL or 32
- Equivalent 50–pin 32
- Right Angle 32
- Receptacle 32
- RS232/422 37
- RS232/422/485 37
- P: Personal computer 40
- S: Servopack 40
- Table 3.13: 40
- 3.2.6 Connection Examples 41
- RS422/485 Interface Cable 43
- Maximum power loss 2.6 W max 44
- Item Specification 44
- Trial Operation 46
- 4.1 Two-Step Trial Operation 47
- (no-load conditions) 49
- Panel operator 50
- P-OT CN1-42 52
- N-OT CN1-43 52
- /S-ON CN1-40 52
- +24VIN CN1-47 52
- Display with the servo ON 53
- Servomotor 54
- Connect to the machine 54
- Before Reading this Chapter 58
- Parameter Configurations 58
- Parameter Signal Setting 61
- Setting Description 61
- Stop Mode After stopping 66
- 5.3 Sequence I/O Signals 67
- Servo amplifier 70
- Host controller 70
- Turns power OFF 71
- ALM output 71
- Figure 5.7 Holding Brake 72
- /S-ON input 74
- /S-RDY CN1-29, 30 75
- Servo Ready Output Signal 75
- CN1-25 /WARN+ 76
- CN1-26 /WARN 76
- A 13 2048 16 to 2048 83
- 16384 16 to 16384 83
- Reference unit: 1Pm 84
- D: Pulley 85
- Ball Screws 87
- Circular Tables 87
- [0.01msec] 89
- 5.6 Absolute Encoders 90
- Battery carrying space 92
- Batter connector (CN8) 92
- Up Cursor Key 93
- Flashes for one second 93
- Flashes for 95
- 1 second 95
- Signal Status Contents 97
- 5.7.3 Program Step Selection 103
- Min. 4 ms 112
- Min. 2 ms 112
- Min. 0 ms 112
- Min. 8 ms 112
- 5.8 Registration 113
- 5.9 Zone Table Set-up 116
- 5.10 Program Table Examples 118
- (Example) 119
- Table 5.14a: Zone Table 121
- Table 15a: Zone Table 122
- Home Position, Pn 823: 125
- 5.12 Homing Routine Operation 126
- Figure 5.13 Jog Speed Table 127
- Serial Commands 130
- 6.1 Specifications (CN6) 131
- 6.2 Control Configuration 132
- 6.3.1 Command Format 134
- 6.3.2 Echo Back Response Time 135
- Table 6.4: 135
- 6.5 Serial Command Functions 137
- 6.5.2 Moving Commands 138
- Table 6.6: Moving Command 138
- Using the Digital Operator 164
- Hand-held Digital Operator 165
- JUSP-0102A-1 165
- Servo Amplifier 165
- 7.1.2 Functions 166
- Built-in Panel Operator 167
- IMPORTANT 168
- 7.1.4 Basic Mode Selection 169
- Dimensional Drawings 170
- Troubleshooting 172
- 9.4 STS Status LEDs 185
- Appendix A 186
- Table A.1: Indexer Parameters 187
- Appendix A-6 191
- Appendix A-7 192
- Appendix A-8 193
- A.3 Servo Amplifier Switches 195
- Appendix A-11 196
- Appendix A-12 197
- Appendix B 198
- B.1 Monitor Modes 199
- Table B.1: Monitor Modes 200
- B.2 Auxiliary Functions 201
- Appendix B-5 202
- Appendix B-6 203
- Appendix C 204
- Appendix C-2 205
- Appendix C-3 206
- Appendix C-4 207
- Appendix D 208
- Appendix D-2 209
- Appendix D-3 210
- Appendix D-4 211
- Appendix D-5 212
- Appendix D-6 213
- Appendix D-7 214
- Appendix D-8 215
- Appendix D-9 216
- Appendix D-10 217
- Appendix D-11 218
- Appendix D-12 219
- Appendix D-13 220
- Appendix D-14 221
- Appendix D-15 222
- Appendix D-16 223
- Appendix D-17 224
- Appendix D-18 225
- Appendix D-19 226
Manuais e produtos relacionados com Equipamento Yaskawa Sigma II Indexer
Equipamento Yaskawa MotionWorks IEC Manual do Utilizador
(396 páginas)
(396 páginas)
Equipamento Yaskawa YTerm Manual do Utilizador
(56 páginas)
(56 páginas)
Equipamento Yaskawa LEGEND-MC Manual do Utilizador
(360 páginas)
(360 páginas)
Equipamento Yaskawa SMC–4000 Manual do Utilizador
(385 páginas)
(385 páginas)
Equipamento Yaskawa MP2000iec Manual do Utilizador
(102 páginas)
(102 páginas)
Equipamento Yaskawa SigmaLogic Manual do Utilizador
(48 páginas)
(48 páginas)
Equipamento Yaskawa MP3200iec Manual do Utilizador
(96 páginas)
(96 páginas)
Equipamento Yaskawa Yasnac PC NC Manual do Utilizador
(389 páginas)
(389 páginas)
Equipamento Yaskawa SGDB Manual do Utilizador
(585 páginas)
(585 páginas)
Equipamento Yaskawa V1000 Manual do Utilizador
(136 páginas)
(136 páginas)
Equipamento Yaskawa A1000 CIMR-AU Manual do Utilizador
(276 páginas)
(276 páginas)
Equipamento Yaskawa MP3200 CPU Manual do Utilizador
(37 páginas)
(37 páginas)
(60 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais