Yaskawa Sigma-5 User Manual: MECHATROLINK-II Commands Manual do Utilizador Página 107
- Página / 142
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5 Command Related Parameters
5.2.6 Acceleration/Deceleration Parameter High-speed Switching Function
5-18
5.2.6 Acceleration/Deceleration Parameter High-speed Switching Function
This function switches, at high-speed, the acceleration/deceleration parameters that are used for positioning
executed by the POSING, FEED, EX_POSING, ZRET, or HOLD commands.
Register the acceleration/deceleration parameter settings in a bank before starting operation, and execute the
bank selector BANK_SEL to switch the acceleration/deceleration parameter settings to those of the registered
bank.
[Bank Selector Allocation]
Allocate the following bank selector BANK_SEL1 in the OPTION field. (The allocation is disabled by
default. Refer to (5) OPTION Field Specifications of chapter 7 Data Field for details on bit allocation meth-
ods.)
[Parameter Bank Setting]
Set the following parameters.
∗ The parameters Pn920 to Pn95F will not be stored in the non-volatile memory. They need to be set every time the
power is turned ON.
[Parameters that Can be Registered as Bank Members]
The following parameters can be registered as parameter bank members among parameters Pn902 to Pn910.
For 4-byte parameters, one parameter must be registered as two consecutive members.
(See Setting Example 2.)
Name Description Setting Data
BANK_SEL1 Bank selector Bank 0 to 15
Parameter No. Name
Data
Size
(byte)
Setting Range
Factory
Setting
Pn900 Parameter Bank Number 2 0 to 16 0
Pn901 Parameter Bank Member Number 2 0 to 15 0
Pn902 to Pn910 Parameter Bank Member Definition 2 0000H to 08FFH 0
Pn920 to Pn95F * Parameter Bank Data 2
0000H to FFFFH
Depends on bank member.
0
Parameter
No.
Name
Data
Size
(byte)
Setting Range Unit
Factory
Setting
Pn80A 1st Linear Acceleration Constant 1 2 1 to 65535
10000
reference units/s
2
100
Pn80B 2nd Linear Acceleration Constant 1 2 1 to 65535
10000
reference units/s
2
100
Pn80C Acceleration Constant Switching Speed 1 2 0 to 65535
100 reference
units/s
0
Pn80D 1st Linear Deceleration Constant 1 2 1 to 65535
10000
reference units/s
2
100
Pn80E 2nd Linear Deceleration Constant 1 2 1 to 65535
10000
reference units/s
2
100
Pn80F Deceleration Constant Switching Speed 1 2 0 to 65535
100 reference
units/s
0
Pn834 1st Linear Acceleration Constant 2 4 1 to 20971520
10000
reference units/s
2
100
Pn836 2nd Linear Acceleration Constant 2 4 1 to 20971520
10000
reference units/s
2
100
Pn838 Acceleration Constant Switching Speed 2 4 0 to 2097152000 Reference unit/s 0
- Σ-V Series 1
- About this Manual 3
- Warranty 4
- (3) Suitability for Use 5
- (4) Specifications Change 5
- Contents 6
- 1.1.1 Layers 10
- 1.1.2 Frame Structure 10
- MECHATROLINK-II Commands 11
- 1.1.4 Terminology 12
- 1 MECHATROLINK-II Commands 14
- 1.4 Data Order 17
- Operation Sequence 18
- 2.1 Preparing for Operation 19
- Setting the Station Address 20
- 2 Operation Sequence 21
- -J11) are Used 23
- (1) Operation Procedure 25
- Controller 26
- 2.3.1 Setup Sequence 27
- POS: Reference position 31
- 3.2.1 No Operation (NOP: 00H) 34
- (4) Details WDT and RWDT 36
- (1) DISCONNECT Command (0FH) 37
- (1) CONNECT Command (0EH) 38
- (2) Details of COM_MOD 39
- (1) SYNC_SET Command (0DH) 40
- (1) ID_RD Command (03H) 41
- (2) Device ID Specifications 42
- ID_RD aSGDV2R9E11A00 43
- ID_RD bSGDV131J11A00 44
- (1) PRM_WR Command (02H) 45
- (1) PPRM_WR Command (1CH) 46
- (1) CONFIG Command (04H) 47
- (1) SENS_ON Command (23H) 48
- • Applicable Commands: 50
- (1) SV_ON Command (31H) 51
- 3.2 Commands Details 52
- (1) SENS_OFF Command (24H) 54
- (1) SV_OFF Command (32H) 55
- (1) PRM_RD Command (01H) 56
- (1) SMON Command (30H) 57
- (1) ALM_RD Command (05H) 58
- (2) ALM_RD_MOD Specifications 59
- (1) ALM_CLR Command (06H) 60
- (1) POS_SET Command (20H) 61
- (2) PS_SUBCMD Specifications 61
- (1) ADJ Command (3EH) 62
- C01EH reference value 65
- C021H reference value 65
- Motion Commands for Operation 66
- 4.1 Motion Commands List 67
- 4.2.1 Stop Motion (HOLD: 25H) 68
- (2) Related Parameters 69
- (1) LTMOD_ON Command (28H) 70
- (2) Normal Latch Mode 70
- (3) Continuous Latch Mode 71
- (4) LT_SGNL Specifications 72
- (5) Related Parameters 72
- (1) LTMOD_OFF Command (29H) 73
- (1) INTERPOLATE Command (34H) 74
- (1) POSING Command (35H) 76
- (1) FEED Command (36H) 78
- (1) LATCH Command (38H) 80
- (1) EX_POSING Command (39H) 82
- (2) Operation 83
- (3) Related Parameters 83
- 4.2.9 Homing (ZRET: 3AH) 84
- (1) VELCTRL Command (3CH) 86
- Before soft-start 87
- After soft-start 87
- Max. motor speed 87
- Pn305 Pn306 87
- (1) TRQCTRL (3DH) 88
- (2) Speed Limit Option 1 89
- (3) Speed Limit Option 2 89
- 5.2.1 Electronic Gear Setting 93
- Position 94
- (2) Position Reference Filter 96
- 5.2.3 Motion Sequence Setting 99
- 5.2.4 Command Data Options 100
- 5 Command Related Parameters 101
- 5.2.4 Command Data Options 101
- (4) OPTION Field Allocation 102
- (1) Latching Allowable Area 104
- (2) Continuous Latch Function 104
- Command Related Parameters 106
- NEAR Signal Width Setting 111
- (3) Option Monitor Setting 113
- MECHATROLINK-II Subcommands 114
- 6.2.1 No Operation (NOP: 00H) 115
- Data Field 120
- 7.1 Main Command Data Field 121
- (1) Applicable Commands 123
- (2) Setting Method 125
- Applicable Commands 126
- 7.1.6 LT_SGNL Specifications 128
- 7.2 Substatus Data Field 129
- Communications or Commands 130
- 8.1 List of Alarms 131
- 8.1 List of Alarms 132
- 8.2 List of Warnings 133
- 8.2 List of Warnings 134
- Appendix 136
- A Brake Control Commands 137
- • Sub-control (SUBCTRL) 139
- Select Motion (MOTION) 140
- Select Latch Signal (L_SGN) 140
- • Sequence Signals: SQ_CMD 140
- Revision History 141
Manuais e produtos relacionados com Equipamento Yaskawa Sigma-5 User Manual: MECHATROLINK-II Commands
(460 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais