Yaskawa Sigma-5 User Manual: MECHATROLINK-II Commands Manual do Utilizador Página 97
- Página / 142
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5 Command Related Parameters
5.2.2 Motion Acceleration/Deceleration Function Setting
5-8
Position Reference Filter Type Selection
Use the ACCFIL bit of the OPTION field to specify the position reference filter type.
Information: While a position reference is being output (STATUS.DEN = 0), the parameter or the filter type
cannot be changed. Wait for completion of the position reference output (STATUS.DEN = 1) to
change the setting.
(3) Linear Deceleration Speed Setting for Commands to Stop a Motor
Set the deceleration speed when using either of the following commands to stop a motor.
• HOLD (When HOLD_MOD = 2)
• SV_OFF (When Pn829 ≠ 0)
Setting for Deceleration to a Stop by Executing HOLD Command (HOLD_MOD = 2)
Setting for Deceleration to a Stop by Executing SV_OFF Command
When SV_OFF command is executed while a motor is running, the servo can be turned OFF after deceleration
to a stop.
When Pn829 is set to 0 (factory setting), the servo will turn OFF immediately upon reception of the SV_OFF
command.
ACCFIL Meaning
0 Without position reference filter
1 Exponential function acceleration/deceleration position reference filter
2 Movement average time position reference filter
HOLD command
(HOLD_MOD=2)
Motor speed
The parameter number in parentheses is when Pn833 = 1.
Pn827 (Pn840)
Parameter
No.
Name
Data
Size
(byte)
Setting Range Unit
Factory
Setting
Pn827 Linear Deceleration Constant 1 for Stopping 2 0 to 65535
10000
reference units/s
2
100
Pn840 Linear Deceleration Constant 2 for Stopping 4 0 to 20971520
10000
reference units/s
2
100
Servo ON status
The parameter number in parentheses is when Pn833 = 1.
SV_OFF command
Servo ON
Pn829
Motor speed
Pn827 (Pn840)
The motor stops
according to Pn001.0
Servo OFF
- Σ-V Series 1
- About this Manual 3
- Warranty 4
- (3) Suitability for Use 5
- (4) Specifications Change 5
- Contents 6
- 1.1.1 Layers 10
- 1.1.2 Frame Structure 10
- MECHATROLINK-II Commands 11
- 1.1.4 Terminology 12
- 1 MECHATROLINK-II Commands 14
- 1.4 Data Order 17
- Operation Sequence 18
- 2.1 Preparing for Operation 19
- Setting the Station Address 20
- 2 Operation Sequence 21
- -J11) are Used 23
- (1) Operation Procedure 25
- Controller 26
- 2.3.1 Setup Sequence 27
- POS: Reference position 31
- 3.2.1 No Operation (NOP: 00H) 34
- (4) Details WDT and RWDT 36
- (1) DISCONNECT Command (0FH) 37
- (1) CONNECT Command (0EH) 38
- (2) Details of COM_MOD 39
- (1) SYNC_SET Command (0DH) 40
- (1) ID_RD Command (03H) 41
- (2) Device ID Specifications 42
- ID_RD aSGDV2R9E11A00 43
- ID_RD bSGDV131J11A00 44
- (1) PRM_WR Command (02H) 45
- (1) PPRM_WR Command (1CH) 46
- (1) CONFIG Command (04H) 47
- (1) SENS_ON Command (23H) 48
- • Applicable Commands: 50
- (1) SV_ON Command (31H) 51
- 3.2 Commands Details 52
- (1) SENS_OFF Command (24H) 54
- (1) SV_OFF Command (32H) 55
- (1) PRM_RD Command (01H) 56
- (1) SMON Command (30H) 57
- (1) ALM_RD Command (05H) 58
- (2) ALM_RD_MOD Specifications 59
- (1) ALM_CLR Command (06H) 60
- (1) POS_SET Command (20H) 61
- (2) PS_SUBCMD Specifications 61
- (1) ADJ Command (3EH) 62
- C01EH reference value 65
- C021H reference value 65
- Motion Commands for Operation 66
- 4.1 Motion Commands List 67
- 4.2.1 Stop Motion (HOLD: 25H) 68
- (2) Related Parameters 69
- (1) LTMOD_ON Command (28H) 70
- (2) Normal Latch Mode 70
- (3) Continuous Latch Mode 71
- (4) LT_SGNL Specifications 72
- (5) Related Parameters 72
- (1) LTMOD_OFF Command (29H) 73
- (1) INTERPOLATE Command (34H) 74
- (1) POSING Command (35H) 76
- (1) FEED Command (36H) 78
- (1) LATCH Command (38H) 80
- (1) EX_POSING Command (39H) 82
- (2) Operation 83
- (3) Related Parameters 83
- 4.2.9 Homing (ZRET: 3AH) 84
- (1) VELCTRL Command (3CH) 86
- Before soft-start 87
- After soft-start 87
- Max. motor speed 87
- Pn305 Pn306 87
- (1) TRQCTRL (3DH) 88
- (2) Speed Limit Option 1 89
- (3) Speed Limit Option 2 89
- 5.2.1 Electronic Gear Setting 93
- Position 94
- (2) Position Reference Filter 96
- 5.2.3 Motion Sequence Setting 99
- 5.2.4 Command Data Options 100
- 5 Command Related Parameters 101
- 5.2.4 Command Data Options 101
- (4) OPTION Field Allocation 102
- (1) Latching Allowable Area 104
- (2) Continuous Latch Function 104
- Command Related Parameters 106
- NEAR Signal Width Setting 111
- (3) Option Monitor Setting 113
- MECHATROLINK-II Subcommands 114
- 6.2.1 No Operation (NOP: 00H) 115
- Data Field 120
- 7.1 Main Command Data Field 121
- (1) Applicable Commands 123
- (2) Setting Method 125
- Applicable Commands 126
- 7.1.6 LT_SGNL Specifications 128
- 7.2 Substatus Data Field 129
- Communications or Commands 130
- 8.1 List of Alarms 131
- 8.1 List of Alarms 132
- 8.2 List of Warnings 133
- 8.2 List of Warnings 134
- Appendix 136
- A Brake Control Commands 137
- • Sub-control (SUBCTRL) 139
- Select Motion (MOTION) 140
- Select Latch Signal (L_SGN) 140
- • Sequence Signals: SQ_CMD 140
- Revision History 141
Manuais e produtos relacionados com Equipamento Yaskawa Sigma-5 User Manual: MECHATROLINK-II Commands
(460 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais